Story chair update

Now where was I?  Keep getting interrupted by courses, stove remodelling, fitting doors, skirting boards, bees etc, etc.

Well yesterday I found I had to split out some more oak for a back panel for the chair.  The butt was not so big, but nonetheless still needed the winch to haul it onto the trailer.  It turned out to be heavily infected with something oak is prone to but which I couldn’t identify, however, the timber that isn’t rotten is a warm brown.  I’ll be making the side wings from it which need to be as light as possible to maintain the bottom heavy weighting for stability.

Here’s me doing some speed splitting – nearly as good as watching paint dry.

(Did I notice the head come off the sledge-hammer?  Really! -Ed)

Today I’ve been fitting the panels in the back.  At first I was going to have them raised with a small upstanding rebate and worked them up so using a fillister plane and a little finishing plane for the chamfer:

SAMSUNG CSC
SAMSUNG CSC

Eventually I decided to go for a less formal fielding without the step as in the East Riddlesden chair:

SAMSUNG CSCIt’s a more colloquial style more fitted for an outdoor location, so here it is dry fitted:

The riven oak is producing some decent grain patterns, the storytellers will need to beware of this eye in the back of their necks!

SAMSUNG CSCNext up will be stopped chamfers to the frame and then the arms and seat, and finally attaching the back frame to the seat frame – no chair has been built like this before (Good job too – Ed)

I rebuilt the stove today as the firebox was just too big; that was what caused the flue fire.  I only need a slow fire to produce smoke in Summer to keep the midges at bay.  I decided to try keeping the smoke a bit more under control by adding a plate from scrap steel plate to join the flue to the fire bricks:

SAMSUNG CSCIt seems to work very well, with almost all the smoke going up the flue.  With the amount of firebrick in there I should be able to cook potatoes in 25 minutes.

On my commute this week a new dwelling has appeared on Silsden Moor, a splendid new shepherd’s hut:

SAMSUNG CSC

All around my hat …

SAMSUNG CSC
SAMSUNG CSC
Well Spring has certainly well and truly sprung and it’s so busy – bees:

SAMSUNG CSCWent to an auction at Brickhill Farm (above) run by Halifax Bee Keepers Association yesterday and there was quite a lot of stuff there, these’re just some of the 300ish lots.

SAMSUNG CSC
I managed to buy a good used hive for a fraction of the cost of a new one:

SAMSUNG CSC

Pine, so I need to treat it with some harmless-to-bees preservative, and get some frames and make them up.

Also I picked up a small smoaker, I’ll be finding out what from my extensive wooden stores smolders nicely.  Maybe I could bottle some of the stuff from the charcoal kiln.

PhotoGrid_1366785790865

There were stock and extensive fruit gardens at the farm where the auction was on the outskirts of Bradford,

English: Bradford Town Hall

Bradford Town Hall (Photo credit: Wikipedia)

 

 

 

 

 

 

 

with added pigs:

SAMSUNG CSC

Back at Strid Wood, rebuilt the stove at the bodgery last week, adding a further dead wheel to the base in hopes of getting the top of the flue well above the tarp to keep the smoke exit level higher.  I’ve got a cough!

SAMSUNG CSC

Fired it up Sunday.  You can see that the flue is now higher than the ridge and more smoak should stay out of the workshop.

SAMSUNG CSC

I fixed the flue up with three scavenged Jubilee clips co-united.  Minutes after I lit it I had a rather hot chimney fire, but managed to put the ridge timbers and ropes out standing on the lathe bed and playing the fireman with the sharpening water luckily.  ‘Worse things at sea.’ As they say when they’re not at sea.

Still hammering away at the shepherd’s chair, here’s some speed axing of part of the back panel (One day, you’re going to fix that unstable chopping block. – Ed):

The axe chips vid that comes up after the axing finishes, is just for people who rather enjoy watching paint dry.

Watch this space for the slowly evolving story chair story.  Got the third of the major tenons fitting today (well nearly).